| SYNCRO-VIEW | Syncro view repeater |
| SYNCRO-MATRIX-CP-M2 | Syncro Matrix-CP-M2 Matrix CP Mimic panel in M2 cabinet ( Max 24 zones) |
| SYNCRO-MATRIX-CP-M3 | Syncro Matrix-CP-M3 Matrix CP Mimic panel in M3 cabinet ( Max 40 zones) |
| SYNCRO-MATRIX-CP-S4 | Syncro Matrix-CP-S4 Matrix CP Mimic panel in S cabinet ( Max 72 zones) |
| SYNCRO-KAU2016 | Fan control Module (SFCM) |
| SYNCRO-KAU2017 | ANC control |
| SIGMA-M2-DOCBOX | Sigma-M2-Docbox |
| SIGMA-M3-DOCBOX | Sigma-M3-Docbox |
| KM-FS-M2 | M2 Flush Sourround |
| KM-FS-M3 | M3 Flush Sourround |
| KM-FS-M4 | M4 Flush Sourround |
| PS406-M3 | Power Supply 24V-5.25A PSU Cabinet, up to 22AH (385Wx520Hx110D) |
| PS406-M3D | Power Supply 24V-5.25A PSU Deep Cabinet, up to 26AH (385Wx520Hx200D) |
| PS407-M2D | Power Supply 24V-2.5A PSU Cabinet, up to 12AH (385Wx310Hx110D) |
| PS-408 | PSU - switch module power supply/charger 10amp |
| PS408-M3D | 10AMP POWER SUPPLY |
| SYNCRO-K545 | Syncro 1/0 4 way conventional detection zone module (Input / output) |
| SYNCRO-K547 | Syncro 8 way relay card |
| SYNCRO-K555 | Syncro Networking |
| SYNCRO-K560 | Syncro 16 channel I/O board ( Input / output) |
| SYNCRO-K586 | Syncro AS loop expansion card |
| SYNCRO-SECRDU | Securiton Control & Display Module |
| SEC-HIM-35 | Hochiki-Securiton Interface Module |
| SEC-HIM-35B | Hochiki-Securiton Interface loop Module for 2nd sensor |
| TAKTIS-S1 | TS1 Cabinet (H) 585 x (W) 420 x (D) 167 |
| TAKTIS-S2 | TS2 Cabinet (H) 710 x (W) 500 x (D) 167 |
| TAKTIS-S3 | TS3 Cabinet (H) 1065 x (W) 560 x (D) 239 |
| TAKTIS-VISION-N | Configurable Fire Alarm Repeater 24V DC |
| TAKTIS-K772 | 16 Channel I/O Board |
| TAKTIS-K791 | 8 Way Relay Board |
| TAKTIS-K792 | 8 Way Conventional Zone Board |
| TAKTIS-K793 | 4 Way Sounder Board |
| TAKTIS-KAU2044 | Taktis Fan Controller (Master Module) |
| TAKTIS-KAU2060 | Taktis 6 x Fan Controller (Slave Module) |
| TAKTIS-KAU2045 | Taktis Ancillary Module |
| TAKTIS-KAU2046 | Taktis LED Module |
| EVAC-SD-FACIA | EVAC-SD-FACIA |
| TAKTIS-SECRDU | TAKTIS-SECRDU |
| TAKTIS-BBS1 | TS1 Battery Box (H) 230 x (W) 420 x (D) 167 |
| TAKTIS-BBS3 | TS3 Battery Box (H) 395 x (W) 560 x (D) 239 |
| TAKTIS-SECRDU | TAKTIS-SECRDU |
| SEC-HIM-35 | Hochiki-Securiton Interface Module |
| SEC-HIM-35B | Hochiki-Securiton Interface loop Module for 2nd sensor |
| TAKTIS-OCKULAR-128 | Taktis graphics software c/w 128 panel network license |
| TAKTIS-OCKULAR-16 | Taktis graphics software c/w 16 panel network license |
| TAKTIS-OCKULAR-4 | Taktis graphics software c/w 4 panel network license |
| VIZULINX-HLI | Vizulinx Gateway Unit K85000 |
| PS-408 | PSU - switch module power supply/charger 10amp |
| TAKTIS-K794 | Taktis Plug In Media Gateway Card |
| ALK-ASN | Analogue Photoelectric Smoke Detector |
| ACB-ASN | Hochiki Multi-Thermal Detector White |
| ACB-ASNW | Analogue Multi-Thermal Detector (Weatherproof) White |
| YBN-R-3(WHT) | Hochiki Analogue Base WHITE |
| YBN-UA(WHT) | Hochiki ALK-ASN Recess mount Base Adaptor |
| CHQ-WS2 | Addressable Loop-Powered Wall Sounder |
| CHQ-WSB | Analogue Wall Sounder Beacon |
| WS2-WPK | Weatherproof Back Box |
| YBO-BS(WHT) | Hochiki Analogue Sounder Base WHITE |
| YBO-BSB(WHT) | Addressable Loop Powered Base Sounder Beacon WHITE |
| CHQ-AB(WHT) | Hochiki addressable Beacon |
| CHQ-ARI(WHT) | Adressable Loop Powered Remote Indicator |
| CHQ-CB(WHT)WL | Addressable Loop-Powered Beacon |
| CHQ-WB(WHT) | Addressable Loop-Powered Wall Beacon |
| CHQ-MRC(SCI) | Analogue Mains Relay Controller |
| CHQ-DIM(SCI) | Hochiki 'Smart-Fix' Dual Input Module |
| CHQ-PCM(SCI) | Analogue Plant Control Module |
| CHQ-PCM-DIN(SCI) | Analogue Plant Control Module - DIN Rail |
| CHQ-DSC(SCI) | Hochiki 'Smart-Fix' Dual Sounder Controler |
| CHQ-DRC-DIN(SCI) | Analogue Dual Relay Controller-DIN Rail version |
| CHQ-DZM(SCI) | Hochiki 'Smart-Fix' Dual Zone Monitor |
| CHQ-SZM(SCI) | Hochiki 'Smart-Fix' Single Zone Monitor |
| CHQ-DZM-IS | Dual Zone Module |
| CHQ-DSC-DIN(SCI) | Dual Sounder Controller- DIN Rail |
| CHQ-DRC | Hochiki 'Smart-Fix' Dual Relay Controller |
| CHQ-DZM-DIN(SCI) | Analogue Dual Zone Module - Din Rail |
| CHQ-DZM-IS-DIN | Analogue IS Compatible Dual Zone Module-DIN Rail |
| CHQ-MRC-DIN(SCI) | Analogue Mains Relay Controller- DIN Rail |
| CHQ-DIM-DIN(SCI) | Analogue Dual Input Module- DIN Rail |
| CHQ-BACKBOX | CHQ Module Back Box |
| CHQ-POM | Hochiki powered output + 2 inputs |
| CHQ-SIM | Hochiki single input module |
| CHQ-ADAPTOR | CHQ Module Adaptor Plate |
| HCP-E-ADD | Hochiki Addressable Manual Call Point |
| HCP-E-ADD-WP | Hochiki Addressable Manual Call Point (Weatherproof) |
| SYNCRO-AAF | Alarm acknowledgement Module |
| TCH-B200 | Hand Held Address Programmer |
| SMB-1 | An IP66 rated, grey (RAL7035) enclosure |
| SMB-2 | IP66 Rated Enclosure- 6DIN Rail Modules |
| SMB-3 | An IP66 rated, grey (RAL7035) enclosure |
| MBB-1 | Hochiki Surface Back Box to suit Marine Detectors |
| YBO-BS-COV | Cover for Analogue Sounder Base IVORY |
| YBO-BS-COV(W) | Cover for Analogue Sounder Base - WHITE |
| DH-98-ASA | Hochiki Analogue Duct Probe |
| YBD-RA | BASE MOUNTING ADAPTOR |
| CHQ-CP | Clean Contact Input Module |
| CHQ-SOM | Single relay output module |
| YBN-R-3(WHT)-SCI | Hochiki Analogue Short Circuit Isolator Base WHITE |
| YBO-R-3(RED) | Hochiki Analogue Base RED |
| ALK-ASN-BLK | Hochiki Analogue Photo Optical Smoke Detector Black |
| DCD-1E-IS(WHT) | Hochiki Intrinsically Safe Conventional Thermal Detector White |
| TAKTIS-AAF | TAKTIS-Hochiki Alarm Acknowledgement Module |
| TAKTIS-BBS1 | TS1 Battery Box (H) 230 x (W) 420 x (D) 167 |
| TAKTIS-BBS2 | Size 2 Battery/Utilities Box |
| TAKTIS-BBS3 | TS3 Battery Box (H) 395 x (W) 560 x (D) 239 |
| ACC-ASN | Hochiki Analogue Multi-Sensor (Optical & Heat) White |
| CHQ-ISM-DIN | Intrinsically Safe Compatible Sounder Module - DIN Enclosure |
| ALD302L | Universal Anti ligature Point Detector mounting base |
| YBN-R-2NA | Hochiki Analogue Base IVORY |
| YBN-R-3(BLK) | Black - Common Mounting Base |
| YBO-BS | Hochiki Analogue Sounder Base IVORY |
| YCA-RL-3H2M | GTP Hochiki Addressable Base |
| ALK-AS | Hochiki Analogue Photo Optical Smoke Detector |
| ACB-AS | Hochiki Multi-Thermal Detector |
| ACB-ASW | Hochiki Multi-Thermal Detector (Weatherproof) |
| YBN-R-2NA | Hochiki Analogue Base IVORY |
| YBO-BS | Hochiki Analogue Sounder Base IVORY |
| CHQ-AB | Hochiki addressable Beacon - RED |
| CHQ-DZM(SCI) | Hochiki 'Smart-Fix' Dual Zone Monitor |
| CHQ-DZM-IS | Dual Zone Module |
| CHQ-DIM(SCI) | Hochiki 'Smart-Fix' Dual Input Module |
| CHQ-MRC(SCI) | Analogue Mains Relay Controller |
| CHQ-DSC(SCI) | Hochiki 'Smart-Fix' Dual Sounder Controler |
| CHQ-SZM(SCI) | Hochiki 'Smart-Fix' Single Zone Monitor |
| CHQ-DRC | Hochiki 'Smart-Fix' Dual Relay Controller |
| CHQ-DZM-DIN(SCI) | Analogue Dual Zone Module - Din Rail |
| CHQ-DZM-IS-DIN | Analogue IS Compatible Dual Zone Module-DIN Rail |
| CHQ-MRC-DIN(SCI) | Analogue Mains Relay Controller- DIN Rail |
| HCP-E-ADD | Hochiki Addressable Manual Call Point |
| HCP-E-ADD-WP | Hochiki Addressable Manual Call Point (Weatherproof) |
| DH-98-ASA | Hochiki Analogue Duct Probe |
| CHQ-ADAPTOR | CHQ Module Adaptor Plate |
| YBO-BS-COV | Cover for Analogue Sounder Base IVORY |
| SMB-1 | An IP66 rated, grey (RAL7035) enclosure |
| SMB-2 | IP66 Rated Enclosure- 6DIN Rail Modules |
| SMB-3 | An IP66 rated, grey (RAL7035) enclosure |
| TCH-B200 | Hand Held Address Programmer |
| CHQ-BACKBOX | CHQ Module Back Box |
| YBD-RA | BASE MOUNTING ADAPTOR |
| CHQ-CP | Clean Contact Input Module |
| YBN-R-3(BLK) | Black - Common Mounting Base |
| YBN-R-3(WHT) | Hochiki Analogue Base WHITE |
| YBO-BSB | Hochiki Addressable Beacon/Sounder Base |
| YCA-RL-3H2M | GTP Hochiki Addressable Base |
| CHQ-WS2 | Addressable Loop-Powered Wall Sounder |
| CHQ-WSB | Analogue Wall Sounder Beacon |
| WS2-WPK | Weatherproof Back Box |
| CHQ-CB(WHT)RL | Hochiki addressable Loop Power VAD - Ceiling Beacon White Body Red Lens |
| CHQ-CB(WHT)WL-15 | Hochiki addressable Loop Power VAD - High Power Ceiling Beacon White Body and Lens |
| YBO-BS(WHT) | Hochiki Analogue Sounder Base WHITE |
| YBO-BSB(WHT) | Addressable Loop Powered Base Sounder Beacon WHITE |
| CHQ-AB(WHT) | Hochiki addressable Beacon |
| CHQ-CB(WHT)WL | Addressable Loop-Powered Beacon |
| CHQ-WB(WHT) | Addressable Loop-Powered Wall Beacon |
| YBO-BS-COV | Cover for Analogue Sounder Base IVORY |
| YBO-BS-COV(W) | Cover for Analogue Sounder Base - WHITE |
| CHQ-ARI(WHT) | Adressable Loop Powered Remote Indicator |
| STR-LAB | Strobe FIRE Label to suitexternal Beacons |
| YBO-BS | Hochiki Analogue Sounder Base IVORY |
| YBO-BSB | Hochiki Addressable Beacon/Sounder Base |
| SIGMA-M2 | Sigma 2 Wire in M2 Cabinet (385Wx310Hx90D) |
| SIGMA-M3 | Sigma 2 Wire in M3 Cabinet (385Wx520Hx110D) |
| SIGMA-2-M2-SFDI | SIGMA-2 ZONE SLIDING FIRE DOOR PANEL |
| SIGMA-2-M2-SFDI-KIT | Fire Door Control Panel Kit |
| SIGMA-M2-DOCBOX | Sigma-M2-Docbox |
| SIGMA-M3-DOCBOX | Sigma-M3-Docbox |
| MATRIX-CP-M3-40 | Matrix-CP Mimic Panel 40 Ind. M3 Cabinet (385Wx520Hx110D) |
| PS406-M3 | Power Supply 24V-5.25A PSU Cabinet, up to 22AH (385Wx520Hx110D) |
| PS406-M3D | Power Supply 24V-5.25A PSU Deep Cabinet, up to 26AH (385Wx520Hx200D) |
| PS407-M2D | Power Supply 24V-2.5A PSU Cabinet, up to 12AH (385Wx310Hx110D) |
| KM-FS-M2 | M2 Flush Sourround |
| KM-FS-M3 | M3 Flush Sourround |
| KM-FS-M4 | M4 Flush Sourround |
| SIGMA-2-M3-MCP | Sigma 2 zone, 2 wire, MCP in M3 Cabinet (385Wx520Hx110D) |
| SOC-AS3 | Conventional Photoelectric Smoke Detector |
| DCD-A3 | Conventional rate of rise & fixed temperature heat detector 60°C |
| DCD-C3 | Conventional rate of rise & fixed temperature heat detector 90°C |
| DFJ-A3 | Conventional Fixed Temperature Heat Detector 60°C |
| DFJ-C3 | Conventional Fixed Temperature Heat Detector 90°C |
| YBN-R-6(WHT) | Conventional Base Hochiki 24V WHITE (3 terminal) |
| YBO-R-6R(WHT) | Conventional Latching Relay Mounting Base WHITE |
| SLV-AS | Conventional Photoelectric Smoke Detector |
| YBO-R-6N(WHT) | Conventional Non-Latching Relay Mounting Base WHITE |
| DCD-A | Conventional Rate of Rise 'Type A' Heat Detector 60°C |
| DCD-C | Conventional Rate of Rise 'Type C' Heat Detector 90°C |
| DFJ-60B | Conventional Fixed Temperature Heat Detector 60°C |
| DFJ-90D | A Conventional Fixed Temperature Heat Detector 90°C |
| DFG-60BLKJ | Waterproof Conventional 60°C Fixed Temperature Heat Detector |
| DRD-AS | A Conventional Flame Detector |
| SPC-AS | A Conventional Beam Smoke Detector |
| YBN-R-4C | Conventional detector mounting base - NO Remote indicator Output - IVORY |
| YBO-R-4 | Conventional detector mounting base IVORY |
| DH-98-ASC | Hochiki Conventional Duct Probe |
| CSBB-E(WHT) | A Conventional Base Sounder Beacon which has been designed to complement the Hochiki conventional range of detectors. |
| CSB-E(WHT) | A Conventional Base Sounder which has been designed to complement the Hochiki conventional range of detectors. |
| YBN-R-4IS(WHT) | Hochiki WHITE Intrinsically Safe Conventional Base |
| YBN-R-6 | Hochiki 24V Conventional Base for DRD-AS |
| YBO-R-6PA(WHT) | Hochiki 24V White Conventional Base for 2 Wire System WHITE |
| ALD302L | Universal Anti ligature Point Detector mounting base |
| YZU-A | Adjustabe Mounting Bracket for DRD-AS detector and Firescape Emergency light |
| YZU-B | Wall Mounting Bracket |
| SIGMA-2-M3-ECU | SIGMA XT EXTINGUISHANT PANEL-2 zone M3 cabinet with 1 x ECU |
| SIGMA-4-M3-ECU | SIGMA XT EXTINGUISHANT PANEL-4 zone M3 cabinet with 1 x ECU |
| SIGMA-8-M3-ECU | SIGMA XT EXTINGUISHANT PANEL-8 zone M3 cabinet with 1 x ECU |
| SIGMA-8-M3D-ECU-5A | SIGMA XT 8 zone M3D cabinet with 1 x ECU, 5A PSU |
| SIGMA-2-M3-ECU-A | SIGMA 2 zone M3 cabinet with C/W aerosol extinguishant control unit |
| SIGMA-4-M3-ECU-A | SIGMA 4 zone M3 cabinet with C/W aerosol extinguishant control unit |
| SIGMA-8-M3-ECU-A | SIGMA 8 zone M3 cabinet with C/W aerosol extinguishant control unit |
| SIGMA-8-M3D-ECU-A-5A | SIGMA 8 zone M3 DEEP cabinet with C/W aerosol extinguishant control unit and 5Amp PSU |
| WS-GEN-ESI | Warning Sign (generic) "Extinguishing System Inoperative" |
| WS-GEN-FA-DNE | Warning Sign (generic) "Fire Alarm/Do Not Enter" |
| WS-GEN-FA-EVAC | Warning Sign (generic) "Fire Alarm/Evacuate Area" |
| WS-GEN-FA-DNE-WP | Warning Sign (Generic) Weatherproof "Fire Alarm Do Not Enter" |
| KM-FS-WS | ECU & WS (Generic) Warning Sign Surround for Flush Fitting |
| ECU-HS | Extinguishant hold off switch |
| ECU-LCS | Sigma Extinguishant Local Control Status Unit with timer (186Wx132Hx55D) |
| ECU-WS-ESI | RS485 Warning Signs: "EXTINGUISHING SYSTEM INOPERATIVE" |
| ECU-WS-FA-DNE | RS485 Warning Signs:"FIRE ALARM DO NOT ENTER" |
| ECU-WS-FA-DNE-WP | RS485 Warning Signs:"FIRE ALARM DO NOT ENTER" (Weatherproof) |
| ECU-WS-FA-EVAC | RS485 Warning Signs:"FIRE ALARM EVACUATE AREA" |
| ECU-WS-FA-EVAC-WP | EVAC Waterprrof Warning Sign |
| STI7520 | Weatherproof clear polycarbonate enclosure with KEY lock (225H x 305W x 92D) |
| STI7521 | Weatherproof clear polycarbonate enclosure with THUMB lock (225H x 305W x 92D) |
| WS-GEN-ESI-WP | Weatherproof Sign (generic) "Extinguishing System Inoperative" |
| WS-GEN-FA-EVAC-WP | Warning Sign (Generic) Fire Alarm Evacuate Area Weatherproof Sign |
| STIRPRS01 | Conventional Resettable RED Manual Call Point - Surface Mount |
| CCP-W-IS | A Conventional Manual Call Point designed for use in hazardous areas and based upon the industry standard KAC world series housing. |
| BANSHEE-MT(WHT) | An Electronic Conventional Sounder which can be installed internally.(WHITE) |
| BEL-SBDB(RED) | An Electronic Conventional Sounder Beacon which can be installed internally. |
| BEL-SBSB(RED) | An Electronic Conventional Sounder Beacon which can be installed internally. |
| BE-SDB | An Electronic Conventional Sounder comes with a deeper IP66 back box, which enables the unit to be installed externally. |
| FLASHNI | Combined Sounder Strobe |
| ROSHNI | Electronic Sounder RED |
| STIIC | Clear PVC integral cover (flap) for STI call point |
| KAC-RED-WP | Weatherproof Conventional Call Point - Red |
| ECU-WS-FA-EVAC-WP | EVAC Waterprrof Warning Sign |
| KAC-RED | Conventional Red Manual Call Point |
| BANSHEE-MT(WHT) | An Electronic Conventional Sounder which can be installed internally.(WHITE) |
| FLASHNI | Combined Sounder Strobe |
| ROSHNI | Electronic Sounder RED |
| BEL-SBDB(RED) | An Electronic Conventional Sounder Beacon which can be installed internally. |
| BEL-SBSB(RED) | An Electronic Conventional Sounder Beacon which can be installed internally. |
| BE-SDB | An Electronic Conventional Sounder comes with a deeper IP66 back box, which enables the unit to be installed externally. |
| A105N | Marine High Output 112db Alarm Sounder - Red 24vDC |
| BEACON-B | 24VDC BLUE Strobe |
| BEXS110 | Flameproof Zone 1 & 2 High Output 117dB(A) Red Alarm Horn |
| STR-LAB | Strobe FIRE Label to suitexternal Beacons |
| CCP-W-IS | A Conventional Manual Call Point designed for use in hazardous areas and based upon the industry standard KAC world series housing. |
| HCP-E-ADD | Hochiki Addressable Manual Call Point |
| HCP-E-ADD-WP | Hochiki Addressable Manual Call Point (Weatherproof) |
| HCP-EM | Marine approved Hochiki addressable call point |
| STIRPRS01 | Conventional Resettable RED Manual Call Point - Surface Mount |
| KAC-GLASS | Spare Glass (Pack of 5) |
| KAC-RED-WP | Weatherproof Conventional Call Point - Red |
| STIIC | Clear PVC integral cover (flap) for STI call point |
| STI6930 | Call Point Stopper (Flush) |
| STI6931 | Call Point Stopper (Surface) |
| STI15C10ML | MCP Guard Euro 32mm Surface NO sounder - Red Fire/ Green Exit label |
| STI15C20ML | MCP Guard Euro 32mm Surface with sounder - Red Fire/ Green Exit label |
| STI13110FR | Universal Stopper (Surface) IP56 No sounder |
| STI13120FRB | MCP Guard with Sounder (word- LIFT/BREAK GLASS) IP56 |
| STI13610FR | Enviro Stopper (No Sounder) IP66 |
| STI13620FR | Enviro Stopper (Includes Sounder) IP66 |
| KAC-FLEX | KAC Flexible element PS210 |
| KAC-KEY | SC070 Spare Key - KAC BGA Pk10 |
| KAC-RED | Conventional Red Manual Call Point |
| KAC-WHITE | Conventional White Manual Call Point - EMERGENCY ALARM |
| EK-WL8-CP-AU | Ekho Wireless resettable MCP |
| STI15010ML | MCP Guard Euro Flush mount NO sounder - Red Fire / Green Exit labels |
| STI15020ML | MCP Guard Euro flush mount with sounder - Red Fire/ Green Exit label |
| STI3150 | STI3150 - Weather Stopper MCP Guard 50mm Surface mount IP54 |
| STIAP1RACN | ALERT POINT LITE EMERGENCY EXIT- RED |
| STIAP2GICN | ALERT POINT LITE EMERGENCY EXIT- GREEN |
| DH1350 | Wall Mount Door Holder 1350 |
| DH1360 | 100 Kgs Door Holder - wall or floor mounting |
| DH1369 | Floor–Mounting Electromagnetic Door Release Unit |
| DH150 | 150mm Post Floor/Wall Mount Door Holder |
| DH300 | 300mm Post Floor/Wall Mount Door Holder |
| DHANVIL | Door holder Anvil 1350 |
| DHWP120 | Weatherproof Wall Mounted Door Holder |
| DRS004 | Door Release Switch |
| REM-CL | Remote Indicator FIRE ALARM IN CEILING |
| REM-CS | Remote Indicator FIRE ALARM IN CONCEALED SPACE |
| REM-RM | Remote Indicator FIRE ALARM IN ROOM |
| DRS004MB | DRS004MB Door Release Surface Mounting Block |
| REM-RF | Remote Indicator ROOF |
| BATT-3.2 | 12V 3.2A/hr Sealed Lead Acid Battery |
| BATT-7 | 12V 7A/hr Sealed Lead Acid Battery |
| BATT-9 | 12V 9A/hr Sealed Lead Acid Battery |
| BATT-12 | 12V 12A/hr Sealed Lead Acid Battery |
| BATT-15 | 12V 15A/hr Sealed Lead Acid Battery 151L x 98W x 95H |
| BATT-18 | 12V 18A/hr Sealed Lead Acid Battery |
| BATT-20 | 12V 20A/hr Sealed Lead Acid Battery |
| BATT-22 | 12V 22A/hr Sealed Lead Acid Battery |
| BATT-24 | 12V 24A/hr Sealed Lead Acid Battery |
| BATT-26 | 12V 26A/hr Sealed Lead Acid Battery |
| BATT-33 | 12V 33A/h Sealed lead acid Battery |
| BATT-45 | 12V 45 A/hr Sealed Lead Acid Battery |
| BATT-55 | 12V 55 A/hr Sealed Lead Acid Battery |
| BATT-65 | 12V 65A/hr Sealed Lead Acid Battery |
| BATT-75 | 12V 75A/hr Sealed Lead Acid Battery |
| BATT-100 | 12V 100A/hr Sealed Lead Acid Battery |
| BATT-SLA-TESTER | DIGITAL SLA Sealed Lead Acid Battery Tester |
| 07352242 | LOCK FOCUS T-HANDLE A/HG-R/CL/3B/E KA CL003 |
| 003CAM | S003 Keyed Cam Lock |
| 003PAD | Lockwood 003 keyed padlock - RED |
| 201003 | RSP LOCKWOOD TYPE 201 CYL KA #003 **NO KEYS |
| 570003 | RSP LOCKWOOD TYPE 570 CYL KA #003 **NO KEYS |
| ABUS003 | ABUS TYPE CORE ASSY 83/45 KA003 |
| PS406-M3 | Power Supply 24V-5.25A PSU Cabinet, up to 22AH (385Wx520Hx110D) |
| PS406-M3D | Power Supply 24V-5.25A PSU Deep Cabinet, up to 26AH (385Wx520Hx200D) |
| PS407-M2D | Power Supply 24V-2.5A PSU Cabinet, up to 12AH (385Wx310Hx110D) |
| PS408-M3D | 10AMP POWER SUPPLY |
| PS-408 | PSU - switch module power supply/charger 10amp |
| WARNSLID | Sliding Fire Door Sign |
| WS-GEN-ESI | Warning Sign (generic) "Extinguishing System Inoperative" |
| WS-GEN-FA-DNE | Warning Sign (generic) "Fire Alarm/Do Not Enter" |
| WS-GEN-FA-EVAC | Warning Sign (generic) "Fire Alarm/Evacuate Area" |
| WS-GEN-FA-DNE-WP | Warning Sign (Generic) Weatherproof "Fire Alarm Do Not Enter" |
| ECU-WS-ESI | RS485 Warning Signs: "EXTINGUISHING SYSTEM INOPERATIVE" |
| ECU-WS-FA-DNE | RS485 Warning Signs:"FIRE ALARM DO NOT ENTER" |
| ECU-WS-FA-EVAC | RS485 Warning Signs:"FIRE ALARM EVACUATE AREA" |
| ECU-WS-FA-DNE-WP | RS485 Warning Signs:"FIRE ALARM DO NOT ENTER" (Weatherproof) |
| WS-GEN-ESI-WP | Weatherproof Sign (generic) "Extinguishing System Inoperative" |
| KM-FS-WS | ECU & WS (Generic) Warning Sign Surround for Flush Fitting |
| WS-GEN-FA-EVAC-WP | Warning Sign (Generic) Fire Alarm Evacuate Area Weatherproof Sign |
| SMOKE-SOLO461 | Solo Cordless Heat Tester Kit |
| SMOKE-SOLO822 | Solo 822 Heat and Smoke Tester Kit to 6m |
| SMOKE-SOLO824 | Solo 824 Heat and Smoke Tester Kit to 8.2m |
| SMOKE-SOLO330 | Solo Smoke Dispenser Unit |
| SMOKE-SOLO424 | Solo 240V Heat Tester Kit |
| SMOKE-SOLO100 | Solo Fibreglass Telescopic Pole - 4.5m |
| SMOKE-SOLO101 | Solo Fibreglass Extension Pole - 1.13m |
| SMOKE-TESTIFIRE6001 | Testifire Smoke & Heat Detector Tester |
| SMOKE-TESTIFIRE6201 | Testifire Smoke, Heat & CO Detector Tester |
| SMOKE-TESTIFIRE2001 | Testifire Smoke, Heat & CO Detector Tester |
| SMOKE-TESTIFIRE1001 | Testifire Smoke, Heat Tester |
| SMOKE-TESTIFIRE-TC3 | Carbon Monoxide Testing Capsule for Testifire Unit |
| SMOKE-TESTIFIRE-TS3 | Smoke Testing Capsule for Testifire Unit |
| DRD-16091 | Handheld Flame Detector Tester |
| SMOKE-SABRE | Eco-friendly aerosol smoke detector testers. |
| SMOKE-TESTIFIRE1000 | Testifire Smoke, Heat Tester HEAD ONLY |
| BATT-SLA-TESTER | DIGITAL SLA Sealed Lead Acid Battery Tester |
| FS-1100 | Spectrex Flame Simualtor Kit for IR3 Multi- IR Flame Detectors |
| FS-1200 | FS-1200 Spectrex Flame Simualtor Kit for UV/IR Flame Detectors |
| SB-2.5 | Smoke Bomb Cartridges (5 pack) |
| SMOKE-PEN | Pen Style Test Smoke Generator |
| SMOKE-SOLO-A5 | SMOKE-SOLO A5 Canned Smoke 250ml General (for SOLO Dispenser) |
| TBF-E | TBF-E Hochiki Beam Filter - Test Kit |
| FSP1200 | Standard installation kit for installing detectors in ceiling spaces (No LED) |
| FSP1200-LED | Installation kit for installing detectors in ceiling spaces with remote LED |
| FSP-1M | 1 metre pole for Famco FSP1200 or FSP1200LED |
| FSP-2M | 2 metre pole for Famco FSP1200 or FSP1200LED |
| FSP-3M | 3 metre pole for Famco FSP1200 or FSP1200LED |
| ALD302L | Universal Anti ligature Point Detector mounting base |
| FBE-BRACKET | Adjustable Bracket for FIREbeam unit or single reflector |
| FIREBEAM-WF | Adjustable wall fixing for FIREbeam or reflector |
| IFD-MB | ADJUSTABLE MOUNTING BRACKET |
| STI8201-SS | STI8200-SS - 50mm Spacer for STI8200-SS Smoke Detector Stopper - Stainless Steel |
| STI8230-W | STI8230-W - Smoke Detector Stopper - Rolled Steel White Surface Mount |
| YZU-A | Adjustabe Mounting Bracket for DRD-AS detector and Firescape Emergency light |
| YZU-B | Wall Mounting Bracket |
| LD-USB-DB9-WIN7 | 10cm Lead, Premium USB to DB9 Serial Converter |
| DUSTOFF | Can Compressed Air |
| LD-DB9-DB9 | Wireless Serial Lead |
| T2312A | 140mm Holesaw (c/w Arbour) |
| IM-2001 | Digital Impedance Meter |
| CLEANSOL | Electronic Cleaning Solvent |
| BUTANE | BUTANE Can Butane Gas to suit GASSOLD |
| WD-40 | WD-40 Anti-Corrosive Lubricant 300gNET |
| EL-DL2-AS | Corridor Down Light |
| EL-DL3-AS | Open Area Down Light |
| NF89-C-AS | High Power Corridor Down Light c/w Battery Spacer |
| NF89-O-AS | High Power Open Area Down Light c/w Battery Spacer |
| EL-DL2-KIT | Emergency Escape Light - Corridor - Standard power (excludes base) |
| EL-DL3-KIT | Emergency Escape Light - Open - Standard Power (Excludes base) |
| NF89-0-KIT | Emergency Escape Light - Open - High Power (excludes base) |
| NF89-C-KIT | Emergency Escape Light - Corridor - High Power (excludes base) |
| EL-24-AS | Exit sign 24M Frame |
| EL-24G-AS | Reflectivr worm , Back plate & Rivets assy |
| EL-24G-S-AS | 24M Lens Straight |
| EL-24G-R-AS | 24M Lens Right |
| EL-24L-KIT | 24 meter emergency exit - Left arrow - single (excludes base) |
| EL-24LD-KIT | 24 meter emergency exit - Left Arrow - double (excludes base) |
| EL-24R-KIT | 24 meter emergency exit - Right Arrow - Single (excludes base) |
| EL-24RD-KIT | 24 meter emergency exit - Right Arrow - Double (excludes base) |
| EL-24SX-KIT | 24m DYNAMIC - Straight -single (excludes base) |
| EL-24LX-KIT | 24m DYNAMIC Left -single (excludes base) |
| EL-24RX-KIT | 24m DYNAMIC Right -single (excludes base) |
| EL-WPK24AS(IP66) | Weatherproof enclosure (IP66) for 24M Exit sign c/w spacers and glands |
| EL-2 | 2 Loop Control Panel for up to 254 luminaires (REQUIRES EL-35VTRANSFORMER) |
| EL-35V | Transformer 35v AC, 222VA (MUST BE USED WITH EL-2 CONTROLPANEL) |
| EL-CAB | Panel to Computer Cable |
| EL-KP | Remote Keypad Controller |
| EL-PM | Phase Monitor Relay Unit |
| EL-BAT450-AS | Emergency Lighting Battery |
| EL-BAT2950-AS | High-Powered Battery (2950mAH) |
| EL-REC40 | Recess Adaptor 24M Exit Sign (without base) |
| NFW68-89-RA | Emergency Light Recess Adaptor (without base) |
| EL-PSU | Bus Controlled Power Supply Unit |
| EL-GRAPH | Graphics Software |
| EL-IMP | Installation and Maintenance Program |
| EL-BDC | Battery Disconnection Card |
| EL-8RC | Relay Card - 8 out put |
| EL-ISOL | RS232 Channel Isolator |
| EL-LAN | Terminal Server TCP/IP-RS232 Converter |
| EL-SWT5 | Ethernet Switch 5 Port |
| EL-SWT8 | Ethernet Switch 8 Port |
| EL-DE | Dome Enclosure (for EL-DL2 & DL3) |
| EL-DEB | Dome Enclosure with Bracket (for EL-DL3) |
| EL-BBA1 | BESA Box Adaptor Plate |
| YZU-A | Adjustabe Mounting Bracket for DRD-AS detector and Firescape Emergency light |
| YZU-B | Wall Mounting Bracket |
| SEC-ASD-531 | Aspirating Smoke Detector, 1 sampling pipe (including SSD 31) |
| SEC-ASD-532 | Aspirating Smoke Detector, 1 sampling pipe (w/o smoke sensor) |
| SEC-ASD-535-1 | Aspirating Smoke Detector, 1 sampling pipe, standard display |
| SEC-ASD-535-2 | Aspirating Smoke Detector, 2 sampling pipe, standard display |
| SEC-ASD-535-3 | Aspirating Smoke Detector, 1 sampling pipe, advanced display |
| SEC-ASD-535-4 | Aspirating Smoke Detector, 2 sampling pipe, advanced display |
| SEC-ASD-533 | Aspirating Smoke Detector, 1 sampling pipe (including SSD 533) |
| SEC-MFS-25 | Magnetic Filter System 25, MFS 25 |
| SEC-WRB-25-ABS | Water retaining box standard, Ø 25 mm, ABS/PC |
| SEC-SSD-31 | Smoke sensor for ASD 531, 0.02 - 10%/m (main alarm threshold) |
| SEC-SSD-532-3 | Smoke sensor for ASD 532, 0.02 - 10%/m (main alarm threshold) |
| SEC-SSD-535-3 | Smoke Sensing Device for ASD 535, 0.02% Obs./m (main alrm thresh.) |
| SEC-ASD-535-VERSCHL | Fastener plate to cover a smoke sensor chamber (50 pcs.) |
| SEC-AMB-31 | Main board for ASD 531 |
| SEC-AMB-32 | Main board for ASD 532 |
| SEC-AMB-35-1 | Main board for ASD 535-1 and -3 |
| SEC-AMB-35-2 | Main board for ASD 535-2 and -4 |
| SEC-BCB-35 | Basic control board for standard display of ASD 535-1 and -2 |
| SEC-ACB-35 | Basic control board for advanced display of ASD 535-3 and -4 |
| SEC-AFS-32 | Air flow sensor for ASD 531/532 |
| SEC-AFS-35 | Air flow sensor for ASD 535 |
| SEC-AFU-32 | Aspirating fan unit for ASD 531/532 |
| SEC-AFU-35 | Aspirating fan unit for ASD 535 |
| SEC-RSL-35 | Rotary Snap Lock for ASD 535 (Set 4pcs) |
| SEC-IPS-35 | Insect protection screen (Set 2pcs) |
| HFT-DG-35 | HFT Solvent Plunger |
| SEC-MF4-25-PVC | 25mm PVC 4 in 1 Pipe Fitting |
| HFTEC25 | Enviro Conduit 25mm Light Grey Coupling |
| HFTESB25 | Enviro Conduit 25mm Light Grey Sweep Bend |
| HFTS2 | STD HFT Conduit 25mm Black 4m length |
| HFT-TTA-35-MN | HFT Solvent Nozzle |
| HFT-PC25 | ENVIRO CONDUIT 25MM PIPE CLIP |
| ASD-EC | 25mm End Cap Clipsal 262/25 |
| ASD-LB | ASD Long Radius Bend |
| ASD-P | 4 Metre ASD Pipe (25mm) |
| ASD-PJ | ASD Straight Coupling |
| ASD-T | Solid T Junction Pipe |
| SEC-CC-25-PVC | Compressed-air connection, Ø 25 mm, PVC |
| SEC-CLIP-2.0-PA | Sampling hole clip red, hole Ø 2 mm, PA (10 pcs.) |
| SEC-CLIP-2.5-PA | Sampling hole clip red, hole Ø 2.5 mm, PA (10 pcs.) |
| SEC-CLIP-3.0-PA | Sampling hole clip red, hole Ø 3 mm, PA (10 pcs.) |
| SEC-CLIP-3.5-PA | Sampling hole clip red, hole Ø 3.5 mm, PA (10 pcs.) |
| SEC-CLIP-4.0-PA | Sampling hole clip red, hole Ø 4 mm, PA (10 pcs.) |
| SEC-CLIP-4.5-PA | Sampling hole clip red, hole Ø 4.5 mm, PA (10 pcs.) |
| SEC-CLIP-5.0-PA | Sampling hole clip red, hole Ø 5 mm, PA (10 pcs.) |
| SEC-CLIP-5.5-PA | Sampling hole clip red, hole Ø 5.5 mm, PA (10 pcs.) |
| SEC-CLIP-6.0-PA | Sampling hole clip red, hole Ø 6 mm, PA (10 pcs.) |
| SEC-CLIP-6.5-PA | Sampling hole clip red, hole Ø 6.5 mm, PA (10 pcs.) |
| SEC-CLIP-7.0-PA | Sampling hole clip red, hole Ø 7 mm, PA (10 pcs.) |
| SEC-CLIP-REV-PA | Maintenance clip red, PA, w/o drilling (10 pcs.) |
| SEC-SF-ABS | Sampling-funnel, ABS |
| SEC-SP-36-PVC | Rosette for sampling tube stiff, PVC |
| SEC-SP-M20-PVC-SET | Sampling point for ceiling duct, M20, Ø 36 mm white, PVC, compl. Set |
| SEC-HEAT-3.0-ABS | Sampling point with heating ABS (Set) Ø 3,0 mm red |
| SEC-HEAT-3.5-ABS | Sampling point with heating ABS (Set) Ø 3,5 mm blue |
| SEC-HEAT-4.0-ABS | Sampling point with heating ABS (Set) Ø 4,0 mm green |
| SEC-HEAT-4.5-ABS | Sampling point with heating ABS (Set) Ø 4,5 mm black |
| SEC-HEAT-5.0-ABS | Sampling point with heating ABS (Set) Ø 5,0 mm brown |
| SEC-HEAT-RESISTOR | Heat Resistor |
| SEC-CCF-25-ABS | Cable Connection Fitting Ø 25 mm, ABS (Set) |
| SEC-SLW-0.5-WT | Silicon litz wire 0,5 mm2, white (order qty must be a multiple of 100) |
| SEC-SLW-0.5-BK | Silicon litz wire 0,5 mm2, black (order qty must be a multiple of 100) |
| SEC-POINTDECAL | SAMPLE POINT DECAL (100 ROLL) |
| SEC-POINTLAB | SAMPLE POINT LABEL RED 50mm x 50mm |
| HFTC25FR | HFT 25mm Pipe Clip Black |
| HFTSSB25 | STD HFT Conduit 25mm Black Sweep Bend |
| HFT-TTA-35 | HFT TTA Solvent 35ml Tube |
| ASD-SPI-SS | Institutional sample point |
| ASD-PCC | ASD 25mm Pipe Clips |
| ASD-SB | ASD-SB - ASD 25mm short radius bend |
| ASD-SP-KIT | ASD Sample Point Kit |
| HFTE2-FDSG | Enviro ASD Pipe 25mm Light Grey 4m length - FDSG |
| HFTFRMA25 | HFTFRMA25 HFT Conduit 25mm Black Threaded Male Adaptor |
| HFTS2-FDSG | STD HFT ASD marked Pipe 25mm Black 4m length |
| HFTSC25 | STD HFT Conduit 25mm Black Coupling |
| SEC-CSC-PLASTIC | Plastic 6mm Capillary Tube Connector |
| SEC-CT | 6mm Natural Capillary Tube for Sample Points |
| SEC-CT(RED) | 6mm Red Capillary Tube for Sample Points |
| SEC-SP-KIT | SEC-SP-KIT Securiton Sample Point Kit |
| SEC-WCU-535 | Securiton ASD freezer point Wiring connection unit Ø 25 mm |
| TAKTIS-SECRDU | TAKTIS-SECRDU |
| SYNCRO-SECRDU | Securiton Control & Display Module |
| SEC-RCU-700 | Remote control unit 1 x touch screen (no frame) |
| SEC-NCU-900 | Network communication unit for RCU |
| SEC-RCU-HC | Standalone wall mounting of the RCU with outer door |
| SEC-RCU-HO | SEC-RCU-HO Wall mount 4RU Housing OPEN for SEC-RCU 494w x 300d |
| SEC-RMF-19-1 | SEC-RMF 19-1 19" mount frame for 1 RCU 700 |
| SEC-RIM-35 | Relay I/F module for ASD 535 |
| SEC-RIM-36 | Relay I/F module for Special Fire Detectors |
| SEC-MCM-35 | Memory card module for ASD 535,with memory card |
| SEC-SD-INDUSTRIAL | SD-Card Industrial 2GB |
| SEC-SIM-35 | Serial I/F Module for RS 485 networking of Special Fire Detectors |
| SEC-SMM-535 | Serial Master Module for networking of Special Fire Detectors |
| SEC-KAB-USB-45 | USB 2.0 cable for connection between ASD 535 and PC |
| SEC-REK-511 | SSD 515 Smoke Detector Box, Ø 25 mm |
| SEC-SSD-515-3S | Smoke Sensing Device for REK 511, 0.3% Obs./m |
| SEC-FBS-25-PC-EFM-5ER | Filter Mat, small, for filter box small (5 pcs.) |
| SEC-WRB-25-PVC | Securiton ASD Water retaining box standard, Ø 25 mm, PVC/PC |
| SEC-DFA-25-3 | Detonation flame arrester, Ø 25 mm (IIC) |
| SEC-DFA-25-2 | Detonation flame arrester, Ø 25 mm (IIB) |
| SEC-DFA-25-1 | Detonation flame arrester, Ø 25 mm (IIA) |
| SEC-ASD-HOUSING-EX | Additional housing for SecuriRAS® ASD 535 (Ex areas) |
| SEC-HIM-35 | Hochiki-Securiton Interface Module |
| SEC-HIM-35B | Hochiki-Securiton Interface loop Module for 2nd sensor |
| SEC-ADB-500 | Automatic blow out device |
| ASD-B-VAL | 20mm PVC Ball Valve |
| SEC-DFU-911 | Dust Filter Unit |
| SEC-DTB-25 | Dirt Trap Box 25 mm |
| SEC-RFC-911 | Replacement cartridge for SEC-DFU-911 |
| SEC-RFC-911VE20 | (Pkt 20) Replacement cartridge for SEC-DFU-911 |
| SEC-RMF-19-2 | 19" mount frame for 2 x RCU 700 |
| ASD-PCC | ASD 25mm Pipe Clips |
| BLAZER-100 | BLAZER 100 - 1 Pipe ASD maintenance Unit |
| BLAZER-200 | BLAZER 200 - 2 Pipe ASD maintenance unit |
| BLAZER-300 | BLAZER 300 - 3 Pipe ASD maintenance unit |
| BLAZER-400 | BLAZER 400 - 4 Pipe ASD maintenance unit |
| SEC-CSC-PLASTIC | Plastic 6mm Capillary Tube Connector |
| SEC-I-7510 | SEC-I-7510 RS-485 Isolated High speed repeater |
| SEC-MFS-25 | Magnetic Filter System 25, MFS 25 |
| SEC-SP-KIT | SEC-SP-KIT Securiton Sample Point Kit |
| SEC-WRB-25-ABS | Water retaining box standard, Ø 25 mm, ABS/PC |
| SEC-D&PL-ASD-CONF-N | Dongle & Partner License ASD Config Networking |
| SEC-D&PL-ASD-CONF | Dongle & Partner License ASD Config |
| SEC-ADW-535-1 | Line Type Heat Detector - one sensing tube |
| SEC-ADW-535-2 | Line Type Heat Detector - two sensing tube |
| SEC-ADW-535-1HDX | Line Type Heat Detector ATEX - one sensing tube |
| SEC-ADW-535-2HDX | Line Type Heat Detector ATEX - two sensing tube |
| SEC-ADW-535-1-ATEX | Line Type Heat Detector ATEX Zone 1 |
| SEC-ADW-TU-6-4-CUZN | Adapter SEC-ADW-TU 6/4 CuZn |
| SEC-ART-535-30-EX-1 | External Temperature Sensor for EX-zones |
| SEC-EP-5-4-CUZN | Sensing tube copper 5/4mm |
| SEC-EP-5-4-ST | End plug for SEC-SJ 5/4 St |
| SEC-EP-6-4-PVDF | End plug PVDF for SEC-SJ 6/4 PVDF |
| SEC-FH-5-3-PA-25 | Flexible Hose Polyamide 5/3mm |
| SEC-GC-5-6-EX | Grounding Clamp |
| SEC-PC-5-6-PA | Pipe clamp - To mount the sensing tube. |
| SEC-PC-5-6-ST | Pipe clamp - To mount the sensing tube. |
| SEC-PC-5-6-STG | Pipe clamp - To mount the sensing tube. With brass stiffener. |
| SEC-PS-TU-5-4-ST | Protection screw |
| SEC-RE-6-5-CUZN | Reduction compression ferrule for SEC-FH 5/3 PA. . |
| SEC-SC-5-4-ST-5 | Sensing-Coil of SEC-TU 5/4 St |
| SEC-SC-5-4-CU-5 | Sensing-Coil of SEC-TU 5/4 Cu 5 m |
| SEC-SC-6-4-PTFE-5M-SET | Sensing-Coil 6/4PTFE with mounting clip |
| SEC-SJ-5-4-ST | Screw Junction straight for SEC-TU 5/4 St |
| SEC-SJ-5-4-CUZN | Sensing tube copper 5/4mm |
| SEC-SJ-6-4-PVDF | Screw junction straight PVDF for SEC-TU 6/4 PTFE |
| SEC-SS-4-CUZN | Stiffener sleeve for SEC-TU 6/4 PTFE |
| SEC-TC-5-4-CU-10 | Test-Coil of SEC-TU 5/4 Cu 10 m |
| SEC-TC-5-4-ST-10 | Test-Coil of SEC-TU 5/4 St |
| SEC-TJ-5-4-ST | T-Junction for SEC-TU 5/4 St |
| SEC-TJ-5-4-CUZN | T-Junction for SEC-TU 5/4 Cu |
| SEC-TJ-6-4-PVDF | T-Junction PVDF for SEC-TU 6/4 PTFE |
| SEC-TU-5-4-CU-50 | Sensing tube copper 5/4mm (50m Roll) |
| SEC-TU-5-4-ST | Sensing tube stainless steel 5/4mm |
| SEC-TU-5-4-CU | Sensing tube copper 5/4mm 3m length |
| SEC-TU-6-4-PTFE-100 | Sensing tube teflon 6/4mm |
| SEC-TU-6-4-PTFE-50 | Sensing tube teflon 6/4mm |
| SEC-TU-6-4-PTFE-EX | SensTube Teflon 6/4mm ExSensTube Teflon 6/4mm Ex |
| SEC-AD-5-6-CUZN-SET | SecuriSens ADW Adapter-Set PA-Teflon |
| SEC-SJ-6-4-CUZN-SET | Screw junction-Set Teflontube (incl SJ 6/4 CuZn, SS4 CuZn) |
| SEC-SS-3-CUZN | SecuriSens ADW Stiffner sleeve brass for SEC-FH 5/3mm (10pcs) |
| SEC-SS-3-ST | SecuriSens ADW Stiffner sleeve Stainless for SEC-FH 5/3mm (10pcs) |
| SEC-ART-535-10 | External Temperature Sensor |
| SEC-RIM-36 | Relay I/F module for Special Fire Detectors |
| SEC-SIM-35 | Serial I/F Module for RS 485 networking of Special Fire Detectors |
| SEC-SMM-535 | Serial Master Module for networking of Special Fire Detectors |
| SEC-SD-INDUSTRIAL | SD-Card Industrial 2GB |
| SEC-BR2032 | Replacement battery for SEC-LMB 35 |
| SEC-M20-VE10 | Cable screw union for SEC-ASD 531/532 and 535 |
| SEC-M25-VE10 | M25 Cable Screw Union |
| FBE-FIREBEAM-XTRA | Conventional Beam Smoke Detector |
| FBE-ESP-FIREBEAM-XTRA | Analogue Addressable Beam Smoke Detector |
| FBE-140KIT160 | FIREBEAM Extra LONG RANGE KIT 140-160M |
| FBE-140KIT160-AF | FIREBEAM Extra ANTIFOG REFLECTOR LONG 140-160M |
| FBE-70KIT140 | FIREBEAM Extra MID RANGE KIT 70-140M |
| FBE-70KIT140-AF | FIREBEAM Extra ANTIFOG REFLECTOR MID 70-140M |
| FBE-ADAPTER | FIREBEAM Extra UNISTRUT ADAPTOR |
| FBE-BRACKET | Adjustable Bracket for FIREbeam unit or single reflector |
| FBE-FOGKIT | FIREBEAM Extra Antifog Kit (Reflector & Cover) |
| FIREBEAM-WF | Adjustable wall fixing for FIREbeam or reflector |
| SEC-ASIS | Air shield for ILIA SOHI |
| SEC-CSRLS-2 | Control unit for 2 ILIA |
| SEC-CSRLS-PRO | Control unit for 2 ILIA PRO |
| SEC-ERHS0712-PRO | Beam Smoke Detector |
| SEC-FAPO | SecuriBeam Pane for Protective Housing for SEC-SOHI |
| SEC-SMLS | Extension module to CSRLS |
| SEC-SOHI | Protective Housing for ILIA |
| SEC-STF4 | Test filter to Beam Smoke Detection |
| SPC-AS | A Conventional Beam Smoke Detector |
| STI9624 | Smoke Beam Cage for Fireray 50/100R |
| STI9625 | Smoke Beam Cage for System Sensor Beam Smoke Detector 6424 |
| TBF-E | TBF-E Hochiki Beam Filter - Test Kit |
| CHQ-DZM-IS | Dual Zone Module |
| KFDO-CS-EX2.51P | Isolated Barrier for Intrinsically safe applications |
| IS-L101L | Intrinsically Safe L.E.D Beacon |
| DCD-1E-IS | Conventional intrinsically safe, Rate of Rise Heat Detector (Ivory) |
| CCP-W-IS | A Conventional Manual Call Point designed for use in hazardous areas and based upon the industry standard KAC world series housing. |
| BEXS110 | Flameproof Zone 1 & 2 High Output 117dB(A) Red Alarm Horn |
| DCD-1E-IS(WHT) | Hochiki Intrinsically Safe Conventional Thermal Detector White |
| SOC-E-IS(WHT) | Hochiki Intrinsically Safe P/O Detector White |
| YBN-R-4IS | Hochiki Intrinsically Safe Conventional Base IVORY |
| YBN-R-4IS(WHT) | Hochiki WHITE Intrinsically Safe Conventional Base |
| TYPE-E-PROBE-60C | 60deg Type E Thermal Probe |
| TYPE-E-PROBE-66C | 66deg Type E Thermal Probe |
| TYPE-E-PROBE-68C | 68deg Type E Thermal Probe |
| TYPE-E-PROBE-70C | 70deg Type E Thermal Probe |
| TYPE-E-PROBE-80C | 80deg Type E Thermal Probe |
| TYPE-E-PROBE-90C | 90deg Type E Thermal Probe |
| TYPE-E-PROBE-100C | 100deg Type E Thermal Probe |
| TYPE-E-PROBE-120C | 120deg Type E Thermal Probe |
| TYPE-E-PROBE-125C | 125deg Type E Thermal Probe with lock nut |
| TYPE-E-PROBE-135C | 135deg Type E Thermal Probe with lock nut |
| TYPE-E-PROBE-140C | 140deg Type E Thermal Probe |
| TYPE-E-PROBE-145C | 145deg Type E Thermal Probe with lock nut |
| TYPE-E-PROBE-150C | 150deg Type E Thermal Probe with lock nut |
| TYPE-E-PROBE-160C | 160deg Type E Thermal Probe |
| TYPE-E-PROBE-200C | 200deg Type E Thermal Probe with lock nut |
| TYPE-E-PROBE-240C | 240deg Type E Thermal Probe |
| LINEAR-068-100 | Digital Linear Heat Detection 68 degrees C 100 metres |
| LINEAR-068-500 | Digital Linear Heat Detection 68 degrees C 500 metres |
| TYPE-E-PROBE-180C | 180deg thermal probe with nut |
| TYPE-E-PROBE-210C | 210 deg Type E Thermal Probe with lock nut |
| TYPE-E-PROBE-220C | 220deg Type E Thermal Probe |
| 20-20MI | Spectrex Mini IR3 Flame Detector |
| 40-40I | Spectrex IR3 Flame Det & Bracket |
| 40-40L | Spectrex UV/IR det. & bracket |
| DRD-16091 | Handheld Flame Detector Tester |
| IFD-MB | ADJUSTABLE MOUNTING BRACKET |
| IFD-E-IS | Infra Red Intrinsically Safe Flame Detector Alloy Housing |
| IFD-E-EXD | Infra Red Flame Detector Alloy Flameproof Housing |
| FS-1100 | Spectrex Flame Simualtor Kit for IR3 Multi- IR Flame Detectors |
| DRD-AS | A Conventional Flame Detector |
| DRD-EM | Hochiki Marine Approved Conventional Flame Detector |
| FS-1200 | FS-1200 Spectrex Flame Simualtor Kit for UV/IR Flame Detectors |
| IFD-E | IR3 Flame Detector Alloy Housing |
| YBN-R-6 | Hochiki 24V Conventional Base for DRD-AS |
| YZU-A | Adjustabe Mounting Bracket for DRD-AS detector and Firescape Emergency light |
| YZU-B | Wall Mounting Bracket |
| SYNCRO-ASM-1M2 | Syncro ASM -1 Hochiki Loop Marine Analogue Addressable Fire Control Panel |
| SYNCRO-ASM-2M2 | Syncro 2 Loop Marine Analogue Addressable Fire Panels |
| ATJ-ENM | Hochiki Marine Analogue Multi Heat Sensor |
| ACC-ENM | Hochiki Marine Analogue Multi Sensor Photo and heat Detector (Ivory) |
| YBN-R-3M | Marine approved analogue base |
| HCP-EM | Marine approved Hochiki addressable call point |
| CHQ-DRC-M(SCI) | Marine approved Dual Relay Controller Hochiki Loop Module |
| CHQ-DSC-M(SCI) | Marine approved Dual Sounder Controller Hochiki Loop Module |
| CHQ-SZM-M(SCI) | Marine approved Single Zone Monitor Hochiki Loop module |
| CHQ-DIM-M(SCI) | Marine approved dual input Hochiki loop module |
| YBO-R-SCIM | Marine approved analogue short circuit isolator base |
| MBB-1 | Hochiki Surface Back Box to suit Marine Detectors |
| A105N | Marine High Output 112db Alarm Sounder - Red 24vDC |
| BEXS110 | Flameproof Zone 1 & 2 High Output 117dB(A) Red Alarm Horn |
| YBN-R-6M | Hochiki Marine Conventional Base IVORY |
| HORN-MARINE | 12 Watt 100V IP67 Marine Horn Speaker |
| ALN-ENM | Hochiki Marine Analogue Photo Optical Smoke Detector |
| DCD-AE3M | Hochiki Marine Conventional Thermal Detector Type A |
| DCD-CE3M | Hochiki Marine Conventional Thermal Detector Type C |
| DRD-EM | Hochiki Marine Approved Conventional Flame Detector |
| HORN-SS | 10Watt 100v IP66 Plastic Marine Horn Speaker |
| SOC-E3NM | Hochiki Marine Conv. P/O Detector |
| SYNCRO-ASM-VIEW | SYNCRO ASM-VIEW Syncro View 'Marine' Local LCD Repeater panel |
| LAAP-S-1 | LEAKalarm Addressable Leak Detection Panel Single Loop |
| LAAP-S-2 | LEAKalarm Addressable Leak Detection Panel 2 Loop |
| LA-WLDM | LEAKalarm Addressable Interface Module - Two Detection Zones |
| LAW-05 | LEAKalarm wire 5 Mt |
| LAW-10 | LEAKalarm wire 10 Mt |
| LA-WLDM-EOL | LEAKalarm End of Line Device |
| LA-WLDP | LEAKalarm Leak Detection Probe - 1 m cable |
| HSVS | "Water Leakage Alarm Activated" - Voice Sounder |
| LA-WLDP-DT | LEAKalarm Probe Drip Tray Mounting Kit |
| LA-WLDP-H | LEAKalarm Probe Height Adjuster |
| SY-BS01 | LEAKalarm Manual Alarm Call Point (Blue, Surface Mount) |
| CHQ-ARI(WHT) | Adressable Loop Powered Remote Indicator |
| YBN-R-3(WHT) | Hochiki Analogue Base WHITE |
| ALD302L | Universal Anti ligature Point Detector mounting base |
| ASD-SPI-SS | Institutional sample point |
| SX-129997 | 30T Stat-X Thermal Generator |
| SX-129998L | 60T Long Stat-X Thermal Generator |
| SX-129999 | 100T Stat-X Thermal Generator |
| SX-130000 | 250T Stat-X Thermal Generator |
| SX-130001 | 500T Stat-X Thermal Generator |
| SX-140000 | 1000MT Stat-X Thermal Generator |
| SX-132161 | Head thermal/manual 70C Brass Horizontal Pull Stat-X (Blue) |
| SX-132163 | Head thermal/manual 95C Brass Horizontal Pull Stat-X (Green) |
| SX-132165 | Head thermal/manual 123C Brass Horizontal Pull Stat-X (Red) |
| SX-132162 | Head thermal/manual 70C Brass Vertical Pull Stat-X (Blue) |
| SX-132164 | Head thermal /Manual 95C Brass Vertical Pull Stat-X (Green) |
| SX-132166 | Head thermal/manual 123C Brass Vertical Pull Stat-X (Red) |
| SX-130006 | Brass Vertical Pull, Manual only |
| SX-130007 | Brass Horizontal Pull, Manual only |
| SX-129984 | 30E Stat-X Electric Generator |
| SX-129985 | 60E Stat-X Electric Generator (This has been replaced by 129985L) |
| SX-129986 | 100E Stat-X Electric Generator |
| SX-129987 | 250E Stat-X Electric Generator |
| SX-129988 | 500E Stat-X Electric Generator |
| SX-129989 | 1000E Stat-X Electric Generator |
| SX-129990 | 1500E Stat-X Electric Generator |
| SX-129991 | 2500E Stat-X Electric Generator |
| SX-130166 | 3/4" NPT - M20 cable gland adaptor - Suits FR cable (Includes plastic gland) 14640 |
| SX-CGM20 | Cable Gland metal 20mm x 1/2" BSP - Suits FR cable |
| SX-132649 | 3/4" NPT- 3/4" BSP stainless steel elbow |
| SX-132648 | 3/4" BSP - 1/2" BSP reducing bush - Suits M20 cable gland |
| SX-129993 | 30/60 SS Stat-X Mount/Bracket 18001 |
| SX-129994 | 100/250MT SS Stat-X Mount/Bracket 18005 |
| SX-132844 | Vehicle Bracket for 100/250MT SS (Heavy Duty) 18006 |
| SX-129995 | Vehicle Bracket for 250/500 18010 |
| SX-129996 | Bracket for 1000/1500/2500 18015 |
| SX-130396 | Vehicle Bracket for 250/500/1000ME/1000MT (Heavy Duty) 18011 |
| SX-130397 | Vehicle Bracket for 1000E/1500E/2500E (Heavy Duty) 18016 |
| SX-045-928 | LV/MV Panel Mounting Bracket |
| SX-130423 | Thermal Switch, Normally Close |
| SX-14670 | Thermal Switch, Normally Open |
| SX-001-930 | Thermal Switch Kit with 300mm fly lead and junction, Normally Close, Red Heatshrink |
| SX-001-931 | Thermal Switch Kit with 300mm fly lead and junction, Normally Open, Black Heatshrink |
| SX-001-926 | Light Vehicle Panel (LVP) |
| SX-47129 | Remote Manual Actuator for LV Panel |
| SX-001-987.1 | End-of-line module for use with LV panels, 1k Ohms |
| SX-001-987.3 | 1k ohm end of line resistor assembly for use with LV panels |
| SX-001-984.4 | In-line brass enclosure with connector block |
| SX-AD185N-0100 | Digital cable 185oC Nylon - 100m |
| SX-H9650 | Linear Heat Detection Cable (White) 229 - 251°C alarm temp. |
| SX-135982 | Cable manual release kit x 1m |
| SX-14688 | Cable pull, black T-handle, 200°F 40ft |
| SX-14667 | Cable pull, red T-handle, 300°F 40ft |
| SX-14683 | Weather-resistant wall-mount cover box |
| SX-87060 | GKW twin core fire rated cable (2 x 0.75mm) |
| SX-103198 | P-Clip 19mm (1 x M6) Suit 1/2" Hose |
| SX-90950 | Rubber Grommet Suit LHD / GKW Twin core |
| SX-66538 | Label - AS5062 IN CASE OF FIRE INITIATE EMERGENCY PROCEDURE |
| SX-66539 | Label - AS5062 IN CASE OF FIRE SAFELY STOP MACHINE |
| SX-66547 | Label - Stat-X WARNING MAY OPERATE AUTOMATICALLY |
| SX-66548 | Label - Stat-X DO NOT ENTER |
| SX-66549 | Label - STAT-X EVACUATE ON SOUNDING OF ALARM |
| SX-137060 | Label - STAT-X CABLE MANUAL RELEASE |
| SX-255-982 | CABLE RS232 CONNECT |
| EK-WL8-CP-AU | Ekho Wireless resettable MCP |
| EK-WL8-EXP-AU | Ekho Wireless Expander Module |
| EK-WL8-H-AU | Ekho Wireless Heat Detector |
| EK-WL8-HS-AU | Ekho Wireless Heat Detector with Built in Sounder |
| EK-WL8-IN-AU | Ekho Wireless Single Input Module |
| EK-WL8-O-AU | Ekho Wireless Optical Smoke Detector |
| EK-WL8-OH-AU | Ekho Wireless Multi-Sensor Detector |
| EK-WL8-OS-AU | Ekho Wireless Optical Smoke Detector with Built in Sounder |
| EK-WL8-OUT-AU | Ekho Wireless Single Output Module |
| EK-WL8-OV-AU | Ekho Wireless Optical Smoke Detector with Built in Voice sounder and VAD |
| EK-WL8-SK-AU | Ekho Wireless Survey Kit |
| EK-WL8-SND-AU | Ekho Wireless wall Sounder |
| EK-WL8-TRH-AU | Ekho Wireless Translator Module for Hochiki ESP loop protocol |
| WLESS-HFC-SBR-23-03-AS | Wireless Wall Sounder VAD WP (inc HFW-SIM-01) |
| WLESS-RSM-BSB-AS | RSM-BSB-AS |
| WLESS-RSM-CP-AS | Wireless Resettable manual call Point |
| WLESS-RSM-EXP-AS | Wireless Expansion Module |
| WLESS-RSM-WS(RED)-AS | RSM-WS-AS(RED) |
| WLESS-RSM-WS(WHT)-AS | Hochiki Wireless Wall Sounder - WHITE |
| WLESS-RSM-WTM-AS | Wire to Wireless Translator Module |
| QE90+ | QE90 Evacuation Panel |
| LMU-4 | 4 Speaker Circuit Line Monitoring Card |
| EVAC-SD-40 | EVACUATION MODULE 40 WATT |
| EVAC-SD-60 | EVACUATION MODULE 60 WATT |
| EVAC-SD-120 | EVACUATION MODULE 120 WATT |
| MIC-N | CB Type Balanced Microphone With Bare Ends |
| SPG100 | 100mm Flush mount speaker |
| SPQF100 | 100mm Quick Fit Speaker |
| SPQF100-B | 100mm Black Quick Fit Speaker |
| SPQF100-LP | 100mm Quick Fit Speaker - Low Profile |
| SPQF200 | 200mm Quick Fit Speaker |
| SMQF-B | 100mm Black Quick Fit Surface |
| SP-C2170 | 100mm (4") 100V 5W Ceiling Speaker White |
| SP-C2171 | 100mm (4") 100V 5W Ceiling Speaker Black |
| HORN-CF2053G | 10W 100V Line ABS AS ISO7240.24 Horn Speaker - Grey |
| SPSM-CF0703 | 100mm (4") 100V 5W Surface Mount Speaker White AS ISO7240.24 |
| SPSM-CF0704 | 100mm (4") 100V 5W Surface Mount Speaker Black AS ISO7240.25 |
| SPSM-CF0715 | 200mm (8") 100V 5W FIRE Speaker White AS ISO7240.24 |
| SPSM-CF0716 | 200mm (8") 100V 5W FIRE Speaker Black AS ISO7240.25 |
| SPSM-CF0720 | 200mm (8") 15W 100V Fire Speaker White AS ISO7240.24 |
| SP-CF2160 | 100mm (4") 100V 5W Ceiling Speaker White AS ISO7240.24 |
| SP-CF2161 | 100mm (4") 100V 5W Ceiling Speaker Black AS ISO7240.25 |
| SP-CF2260 | 100mm (4") 100V 5W Alum. Grille Ceiling Speaker White AS ISO7240.24 |
| SP-CF2261 | 100mm (4") 100V 5W Alum. Grille Ceiling Speaker Black AS ISO7240.25 |
| SPSM-CF0716 | 200mm (8") 100V 5W FIRE Speaker Black AS ISO7240.25 |
| SPSM-CF0720 | 200mm (8") 15W 100V Fire Speaker White AS ISO7240.24 |
| HORN-CF2053B | 10W 100V Line ABS AS ISO7240.24 Horn Speaker - Black |
| HORN-CF2053R | 10W 100V Line ABS AS ISO7240.24 Horn Speaker -RED |
| HORN-CF2053W | 10W 100V Line ABS AS ISO7240.24 Horn Speaker - White |
| HORN-SS | 10Watt 100v IP66 Plastic Marine Horn Speaker |
| SP-CF2134 | 200mm (8”) 100V 5W Ceiling EWIS Speaker White Grille AS ISO7240.24 |
| HORN-C2050 | 10W 100V HORN SPEAKER IP66 (EWIS) + DOG LEG BRACKET |
| HORN-C2053 | 10W 100V HORN SPEAKER IP66 (EWIS) |
| HORN-CAGE | HORN-CAGE Horn Ceiling Mount Speaker Cage Black 230 x 230 x 330mm |
| HORN-CAGEW | HORN-CAGEW Horn Speaker Cage WALL mount Black 260 x 260 x 360mm |
| SP-C2126B | 200mm 15W 100V Twin cone FASTFIX steel grill speaker |
| SP-CF2142 | 100v 15W Low Profile Speaker White Grille AS ISO7240.24 |
| STI9627 | Wire Horn Speaker Guard 400m x 400mm x 400mm |
| BEACON-A | 24VDC Amber Strobe |
| STRRED-AMB-LP | Red & Amber Strobe Set on Metal Plate |
| STRRED-AMB-WP | Weatherproof Red & Amber Strobe Set |
| FLASHNI | Combined Sounder Strobe |
| ROSHNI | Electronic Sounder RED |
| IS-L101L | Intrinsically Safe L.E.D Beacon |
| BEACON-WB-R | Flashni Beacon |
| CSB-E(WHT) | A Conventional Base Sounder which has been designed to complement the Hochiki conventional range of detectors. |
| BEL-SBDB(RED) | An Electronic Conventional Sounder Beacon which can be installed internally. |
| BEL-SBSB(RED) | An Electronic Conventional Sounder Beacon which can be installed internally. |
| BE-SDB | An Electronic Conventional Sounder comes with a deeper IP66 back box, which enables the unit to be installed externally. |
| BS-SOL-LX-C-WF-R1-S | Beacon - LX Ceiling, white flash, red body, shallow base AS ISO7240-23:2013 |
| BS-SOL-LX-C-RF-R1-S | Beacon - LX Ceiling, red flash, red body, shallow base AS ISO7240-23:2013 |
| BS-SOL-LX-W-RF-R1-S | Beacon - LX WALL, red flash, red body, shallow base |
| BS-SOL-LX-W-RF-W1-S | Beacon - LX WALL, red flash, WHITE body, shallow base |
| BS-SOL-LX-W-WF-R1-S | Beacon - LX WALL, WHITE flash, red body, shallow base |
| BS-SOL-LX-W-WF-W1-S | Beacon - LX WALL, WHITE flash, WHITE body, shallow base |
| BS-SOL-LX-C-WF-W1-S | Beacon - LX Ceiling, white flash, white body, shallow base AS ISO7240-23:2013 |
| BEACON-BANSHEEFD | Flashdome Red LED Beacon Deep Base IP66 |
| ROSHNI-W | WHITE 9-28VDC Electronic Sounder |
| BS-ROLP-R1-LX-W-WF | Sounder Beacons - RoLP LX Wall |
| KAC-WHITE-WP | Conventional White Waterproof Manual Call Point |
| STI9644 | RED- AMBER Dual strobe wire guard |
| STI6720 | Break Glass Keybox - Red 105mm Dia x 30mm D |
| STI6200 | FIRE EXTINGUISHER THEFT STOPPER |
| STIAP1RACN | ALERT POINT LITE EMERGENCY EXIT- RED |
| STIAP2GICN | ALERT POINT LITE EMERGENCY EXIT- GREEN |
| STI9605 | Wire Detector Guard S/Mount 145mmI/Depth x 214mmI/Dia |
| STI9615 | Wire Sounder & Beacon Guard 90mmI/Depth x 95mmI/Dia |
| STI9627 | Wire Horn Speaker Guard 400m x 400mm x 400mm |
| STI9604 | Detector Guard Flush mt 75mm I/Depth x 175mm I/Dia |
| STI9615 | Wire Sounder & Beacon Guard 90mmI/Depth x 95mmI/Dia |
| STI9624 | Smoke Beam Cage for Fireray 50/100R |
| STI9625 | Smoke Beam Cage for System Sensor Beam Smoke Detector 6424 |
| STI9627 | Wire Horn Speaker Guard 400m x 400mm x 400mm |
| STI6930 | Call Point Stopper (Flush) |
| STI6931 | Call Point Stopper (Surface) |
| STI15C10ML | MCP Guard Euro 32mm Surface NO sounder - Red Fire/ Green Exit label |
| STI15C20ML | MCP Guard Euro 32mm Surface with sounder - Red Fire/ Green Exit label |
| STI13120FRB | MCP Guard with Sounder (word- LIFT/BREAK GLASS) IP56 |
| STI9644 | RED- AMBER Dual strobe wire guard |
| STI8200-W | Smoke Detector GUard - white Flush mount |
| STI8230-SS | Smoke Detector Guard - Stainless Steel Surfcae mount |
| STI13610FR | Enviro Stopper (No Sounder) IP66 |
| STI13620FR | Enviro Stopper (Includes Sounder) IP66 |
| STI6560 | Keypad protector with key lock |
| STI6930 | Call Point Stopper (Flush) |
| STI7500E | Clear polycarbonate enclosure/cover with key lock facility |
| STI7510E | Clear polycarbonate enclosure/cover with thumb lock facility |
| STI7520 | Weatherproof clear polycarbonate enclosure with KEY lock (225H x 305W x 92D) |
| STI7530 | Clear polycarbonate enclosure with key lock |
| STI7550 | Extra large polycarbonate enclosure with key lock |
| STI8200-W | Smoke Detector GUard - white Flush mount |
| STI9624 | Smoke Beam Cage for Fireray 50/100R |
| STI9625 | Smoke Beam Cage for System Sensor Beam Smoke Detector 6424 |
| STI9644 | RED- AMBER Dual strobe wire guard |
| STI15010ML | MCP Guard Euro Flush mount NO sounder - Red Fire / Green Exit labels |
| STI15020ML | MCP Guard Euro flush mount with sounder - Red Fire/ Green Exit label |
| STI6506 | Euro Stopper 32mm Spacer |
| HORN-CAGE | HORN-CAGE Horn Ceiling Mount Speaker Cage Black 230 x 230 x 330mm |
| HORN-CAGEW | HORN-CAGEW Horn Speaker Cage WALL mount Black 260 x 260 x 360mm |
| STI13110FR | Universal Stopper (Surface) IP56 No sounder |
| STI13120EG | STI13120EG - Manual Call Point Guard with Sounder - GREEN |
| STI14100NC | STI14100NC - Universal Stopper Low Profile No Sounder Clear Surface mount IP54 |
| STI3150 | STI3150 - Weather Stopper MCP Guard 50mm Surface mount IP54 |
| STI7521 | Weatherproof clear polycarbonate enclosure with THUMB lock (225H x 305W x 92D) |
| STI8201-SS | STI8200-SS - 50mm Spacer for STI8200-SS Smoke Detector Stopper - Stainless Steel |
| STI8230-W | STI8230-W - Smoke Detector Stopper - Rolled Steel White Surface Mount |
| STI9110 | Thermostat Protector (Large) |
| CHQ-WS2 | Addressable Loop-Powered Wall Sounder |
| CHQ-WSB | Analogue Wall Sounder Beacon |
| WS2-WPK | Weatherproof Back Box |
| BS-SOL-LX-C-WF-R1-S | Beacon - LX Ceiling, white flash, red body, shallow base AS ISO7240-23:2013 |
| BS-SOL-LX-C-RF-R1-S | Beacon - LX Ceiling, red flash, red body, shallow base AS ISO7240-23:2013 |
| BS-SOL-LX-W-RF-R1-S | Beacon - LX WALL, red flash, red body, shallow base |
| BS-SOL-LX-W-RF-W1-S | Beacon - LX WALL, red flash, WHITE body, shallow base |
| BS-SOL-LX-W-WF-R1-S | Beacon - LX WALL, WHITE flash, red body, shallow base |
| BS-SOL-LX-W-WF-W1-S | Beacon - LX WALL, WHITE flash, WHITE body, shallow base |
| BS-SOL-LX-C-WF-W1-S | Beacon - LX Ceiling, white flash, white body, shallow base AS ISO7240-23:2013 |
| BS-ROLP-R1-LX-W-WF | Sounder Beacons - RoLP LX Wall |
| CHQ-CB(WHT)RL | Hochiki addressable Loop Power VAD - Ceiling Beacon White Body Red Lens |
| CHQ-CB(WHT)WL-15 | Hochiki addressable Loop Power VAD - High Power Ceiling Beacon White Body and Lens |
| CWST-RR-S5 | Conventional Beacon(VAD) - Red Case- Red LED |
| CWST-RR-W5 | Conventional Beacon (VAD)- Red Case- Red LED- IP65 |
| CWST-RW-S5 | Conventional Beacon (VAD)- Red Case -White LED |
| CWST-RW-W5 | Conventional Beacon(VAD) - Red Case -White LED- IP65 |
| CWST-WR-S5 | Conventional Beacon(VAD) - White Case - Red LED |
| CWST-WR-W5 | Conventional Beacon(VAD) - White Case- Red LED- IP65 |
| CWST-WW-S5 | Conventional Beacon(VAD) - White Case - White LED |
| CWST-WW-W5 | Conventional Beacon(VAD)- White Case- White LED- IP65 |
| STR-LAB | Strobe FIRE Label to suitexternal Beacons |
| BANSHEE-MT(WHT) | An Electronic Conventional Sounder which can be installed internally.(WHITE) |
| FLASHNI | Combined Sounder Strobe |
| ROSHNI | Electronic Sounder RED |
| BEL-SBDB(RED) | An Electronic Conventional Sounder Beacon which can be installed internally. |
| BEL-SBSB(RED) | An Electronic Conventional Sounder Beacon which can be installed internally. |
| BE-SDB | An Electronic Conventional Sounder comes with a deeper IP66 back box, which enables the unit to be installed externally. |
| CHQ-CB(WHT)RL | Hochiki addressable Loop Power VAD - Ceiling Beacon White Body Red Lens |
| CHQ-CB(WHT)WL-15 | Hochiki addressable Loop Power VAD - High Power Ceiling Beacon White Body and Lens |
| BEACON-WB-R | Flashni Beacon |
| CSB-E(WHT) | A Conventional Base Sounder which has been designed to complement the Hochiki conventional range of detectors. |
| BEACON-BANSHEEFD | Flashdome Red LED Beacon Deep Base IP66 |
| ROSHNI-W | WHITE 9-28VDC Electronic Sounder |
| CWST-WW-S5 | Conventional Beacon(VAD) - White Case - White LED |
| CWST-WW-W5 | Conventional Beacon(VAD)- White Case- White LED- IP65 |
| CWST-WR-S5 | Conventional Beacon(VAD) - White Case - Red LED |
| CWST-WR-W5 | Conventional Beacon(VAD) - White Case- Red LED- IP65 |
| CWST-RW-S5 | Conventional Beacon (VAD)- Red Case -White LED |
| CWST-RW-W5 | Conventional Beacon(VAD) - Red Case -White LED- IP65 |
| CWST-RR-S5 | Conventional Beacon(VAD) - Red Case- Red LED |
| CWST-RR-W5 | Conventional Beacon (VAD)- Red Case- Red LED- IP65 |
| A105N | Marine High Output 112db Alarm Sounder - Red 24vDC |
| BEACON-B | 24VDC BLUE Strobe |
| BEXS110 | Flameproof Zone 1 & 2 High Output 117dB(A) Red Alarm Horn |
| STR-LAB | Strobe FIRE Label to suitexternal Beacons |
|
